PERFORMANCE
RANGE
| Flow
Rate |
upto
1710 LPH. |
 |
| Dynamic
Head |
upto
75 m. |
| Operating
Limits |
|
| Maximum
Water Temprature |
+60oC |
| Maximum
Ambient Temprature |
+45oC |
|
|
Ratings
0.37kW
(0.5 HP) to 1.5 kW (2.0 HP) with Single Phase and Three Phase option. |
Voltage
Range
Single Phase 160 V to 250 V
Three Phase 300 V to 456 V |
DESIGN
PRINCIPLE
The AJP
/ AMJP / AJPM series of Jet Centrifugal Pumps are suitable
for suction from Deep Wells. Closed type Centrifugal Impellars and
a Venturi Jet System ensure satisfactory performance with a Self
- Priming characteristics. The Venturi System is a special accessory
connected at the lower end with a two pipe system interconnecting the
delivery and suction pipes. At the first start water is filled in the
suction pipe. Thereafter, as the pump operates the output water is partly
recirculated through the Venturi Jet System creating a vaccum and in
turn increasing the pressure. This principle results in a two - fold
benefit - 'Pumping from deep wells' as also 'Self Priming'. These pumps
are practically unaffected by the presence of large amounts of entrained
air in the water being pumped.
PUMP
APPLICATION AND INSTALLATION
Jet Centrifugal Pumps can perform at various suction lifts. AJP
/ AJPM / AMJP series Pumps can be selected based on the requirements
as shown in the performance charts. All pumps are suitable for pumping
clean & clear water, not containing abrasive particles aggressive to
the pump components, from a minimum bore well size of 100 mm (4").
Common applications are marginal farming / orchards / residential buildings
/ bunglows / hotels / hospitals / clubs / lawn sprinklers / car - washing
/ boosting water supply for high pressure pumping application / water
circulation.
These pumps are easy to install and can be placed at ground level directly
over bore-wells and require minimum floor space. The pumps must preferably
be installed in a covered area protected against weather and
can be mounted horizontally or vertically as recommended
in the installation
diagram. These pumpsets are strictly not to be run in dry condition
even for testing purpose since it will damage the mechanical seal provided
for protection against leakage & ingress of water into the motor.
SALIENT
FEATURES
| Pump |
| All
pumps are designed for High Heads compared to Power requirements
& Low noise levels. |
| •
Volute Casing
|
Cast
iron - high efficiency, reliability and consistency of performance.
|
| •
Impeller |
Bronze
- high tensile strength - longer life. |
| •
Jet Assembly |
Manganese
Bronze - high tensile strength - longer life. |
| •
Mechanical Seal |
Ceramic
and Graphite - higher life. |
| Motor |
| Totally
enclosed fan cooled ( TEFC ) for continuous operation - single phase.
|
| •
Insulation
|
Class
' F' - higher life and reliability
|
| •
Single Phase Motors |
Permanent
Split Capacitor - No centrifugal switch - higher reliability |
| •
Thermal Protector |
Built
-in thermal protector for single phase motors only - higher
reliability. |
| •
Body |
Cast
Iron - Rugged construction |
| •
Shaft |
Stainless
steel grade - AISI 410 - higher life. |
| •
Bearings |
Sealed
Ball bearings - greased for life of reputed make (generally SKF)
|
| •
Protection |
IP
54. |
ACCESSORIES
Cast Iron
Pressure Regulating valve with spring loaded and hydraulically actuated
Diaphragm to avoid surge in the pipe. Accurate and reliable pressure
setting is possible with the help of the valve which is provided with
the pressure guage.
WARRANTY
One year from date of supply
Note - The Product shown may differ from the actual supply in view of
continuous changes in Design.
Performance
subject to continuous improvement.
